PMBUS PROGRAMMER [IOR] IR DUAL MODE ONLINE/OFFILINE SUPPORT OFFLINE ADAPTER For Graphics Cards,pc motherboard,laptop GPU Infineon

[Admin]

• 
  
  
  
  
  PMBUS IOR/IR/XDP/CHL/ASP PROGRAMMER
  Features:
  Support Online/Offline mode ( connect to motherboard directly , or in some cases we need to solder the ic on the offiline adapter )
  All Requirements Support
  3V,1.8V,SCL,SDA
  EN/PE,IREF,IREF2,PGOOD,SALRT
  ESD Protections , Indicators
  Read & Write program
  Monitor functions online and offline
  Change parameters
  Support backup one chip or all systems ( multi chip together )
  PMBUS PROGRAMMER CHIP SUPPORT LIST:
  • SUPPORT
    IR35201,IR35203,IR35204,IR35217,IRPS5401,IR38263
    IR38265,IR38163,IR38164,IR38363,IR38165,IR38365
    IR38060,IR38062,IR.8063,IR38064,IR3590,IR3595
    IR3588,IR3596,IR36021,IR3563B,IR3564B,IR3565B
    IR3567B,IR3570B,IR3585B,IR35211,IR35218,IR3580
    IR3581,IR3584,IR3591,XDPE11280A,IR35207,IR35209
    IR25210,IR35212,IR35215 , MORE
    OFFLINE ADAPTER IR35201,IR3580,XDPE132G5D,IR3595,IR3567,ASP1300,IR3563,IR35217,IR3570,CHL8228,ASP1251,CHL8325,IR3541,IR3564,IR35204
  IOR READ,WRITE & Modify REGISTER Program :
• 
  
  
  
  
  According to the schematic, pin 24 is SDA and pin 25 is SCL in the PMBus section.
  Solder SDA, SCL, and GND, then connect the programmer to your computer and power on the device.
  If you’re using an offline adapter, first solder the chip, then connect the adapter to the programmer before connecting the programmer to your computer.
  Software Setup
  Open IR PowIRCenter or XDPDesigner, depending on the chip type.
  When the programmer connects successfully, the status indicator in the lower-left corner will turn green.
  Click the Auto Populate Devices icon (first icon on the left).
  All connected chips will be displayed under Total Pout (e.g., IR35217, IR3580 if both are connected).
  Select the desired chip from the list to display its register map, where you can view and modify parameters.
  Backing Up the Program
  To back up the current program, click Save Config File.
  If a user password prompt appears, simply ignore it and click Continue.
  The file will be saved in .txt format, which you can use later.
  Alternatively, you can save the entire board data by clicking File > Save Board Design, which generates a PCB data file.
  Writing a Program
  To write a configuration, click Load Config File and select the desired .txt file.
  Then click Write All Reg to program the chip.
  Utilities & Diagnostics
  The software also offers several utilities under the Utilities menu.
  For example, selecting SalemDevice will display a counter showing how many times the chip has been programmed (some chips have a write limit).
  Clicking Check MTP will reveal additional memory/programming details.
  Selecting Device Status will display a phase fault report to help diagnose potential hardware damage.
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  LINK OF THE PROGRAMMER : ALEXSOF