Vertyanov Successor Programmer Motherboard Profiles - MB connection NUVOTON List

[Admin]

Vertyanov Successor Programmer Motherboard Profiles - MB connection NUVOTON List
Based on Schematic , Boardview
LAR-1 KB_pins=36 LEFT DOWN 05MM FLASH=256 JENK=13 TCK=7 TMS=18 TDI=22 TDO=4 (evserv) NPCE288GA0DX
LAR-2 KB_pins=36 LEFT DOWN 05MM FLASH=384 JENK=7 TCK=13 TMS=11 TDI=14 TDO=17 (evserv) NPCE68BPA1DX

LBB-1 KB_pins=32 LEFT DOWN 05MM FLASH=256 JENK=13 TCK=7 TMS=18 TDI=22 TDO=4 (tested kinoxa)
LBB-2 KB_pins=32 LEFT DOWN 05MM FLASH=256 JENK=13 TCK=7 TMS=18 TDI=22 TDO=4 NPCE388PB0BX (Pityu) TESTED_OK
LC56-14T KB_pins=34 LEFT DOWN 08MM FLASH=256 JENK=20 TCK=16 TMS=14 TDI=9 TDO=17 NPCE388PB0DX (Bilal)
LKL-1 KB_pins=40 LEFT DOWN 05MM FLASH=256 JENK=13 TCK=7 TMS=18 TDI=22 TDO=4 (evserv)
LKL-2 KB_pins=40 LEFT DOWN 05MM FLASH=256 JENK=13 TCK=7 TMS=18 TDI=22 TDO=4 (evserv)
LLA-1 KB_pins=32 LEFT DOWN 05MM FLASH=256 JENK=7 TCK=13 TMS=11 TDI=14 TDO=17 (evserv)
LCL-1 KB_pins=32 LEFT DOWN 05MM FLASH=256 JENK=11 TCK=7 TMS=24 TDI=23 TDO=21 (evserv)

LA-B091P (JKB1) KB_pins=26 LEFT 1MM JENK=7 TCK=19 TMS=20 TDI=21 TDO=10
LA-B092P (JKB1) KB_pins=26 LEFT 1MM JENK=7 TCK=19 TMS=20 TDI=21 TDO=10
LA-B102P KB_pins=26 LEFT JENK=7 TCK=19 TMS=20 TDI=21 TDO=10
LA-B921P KB_pins=26 LEFT JENK=26 TCK=14 TMS=13 TDI=12 TDO=21
LA-C251P KB_pins=26 LEFT JENK=1 TCK=13 TMS=14 TDI=15 TDO=6
LA-C311P KB_pins=26 LEFT JENK=7 TCK=19 TMS=20 TDI=21 TDO=10
LA-D061P KB_pins=26 LEFT DOWN 08MM JENK=7 TCK=19 TMS=20 TDI=21 TDO=10
LA-D131P KB_pins=26 LEFT JENK=26 TCK=14 TMS=13 TDI=12 TDO=21
LA-C421P KB_pins=32 LEFT DOWN 05MM JENK=7 TCK=19 TMS=20 TDI=21 TDO=10
LA-D451P KB_pins=32 LEFT JENK=20 TCK=8 TMS=7 TDI=6 TDO=17
LA-D541P KB_pins=32 LEFT JENK=20 TCK=8 TMS=7 TDI=6 TDO=17
LA-D562P KB_pins=32 LEFT DOWN 08MM JENK=20 TCK=8 TMS=7 TDI=6 TDO=17
LA-E221P KB_pins=32 LEFT DOWN JENK=20 TCK=8 TMS=7 TDI=6 TDO=17
LA-E451P (JKB1) KB_pins=32 LEFT 08MM JENK=20 TCK=8 TMS=7 TDI=6 TDO=17
LA-E581P KB_pins=30 LEFT DOWN 08MM JENK=20 TCK=8 TMS=7 TDI=6 TDO=17

NM-D391 KB_pins=40 LEFT DOWN 05MM FLASH=384 JENK=7 TCK=13 TMS=11 TDI=14 TDO=17 NPCE68BPA0DX 0x0FE2201F (Äèìà_MD)
NM-C741 KB_pins=40 LEFT DOWN 05MM FLASH=256 JENK=7 TCK=13 TMS=11 TDI=14 TDO=17 NPCE68APA0DX 0x0FE2201F (evserv)
NM-C631 KB_pins=40 LEFT DOWN 05MM FLASH=256 JENK=7 TCK=13 TMS=11 TDI=14 TDO=17 NPCE68APA0DX 0x0FE2201F (evserv)


// Listed below are not currently supported EC!
NM-C262 KB_pins=40 LEFT DOWN 05MM FLASH=256 JENK=7 TCK=13 TMS=11 TDI=14 TDO=17 (evserv) NPCX897KA0BX 0x4BA00477
NM-C651 KB_pins=40 LEFT DOWN 05MM FLASH=256 JENK=7 TCK=13 TMS=11 TDI=14 TDO=17 (evserv) NPCX897KA0BX 0x4BA00477

 

[CGTEC]

NPCX897KA0BX NPCX997KA0BX not suported

 

[PunkPunk]

Γεια στο φόρουμ, είμαι νέος εδώ. Αντιμετωπίζω το ίδιο θέμα. Αγόρασα το lenovo x390 yoga με κλειδωμένη την καρφίτσα επόπτη και δεν βρίσκω λύση, το τσιπ nuvoton είναι (NPCE388PB0BX)

 

[RafiManch]

Hello,
This is more of the question to programmer creators, I think.
Has anyone found solution how to read/write EC NPCX897KA0BX ?
I know method through keyboard connector is not working yet.
Has anyone tried to use JTAG programing like it is done for MEC Chips ?
To program this KBC chip under the MEC mode of programmer.
In motherboard NM-C262 soldering the resistor REC10 (1kΩ/5%, package 0402) to the board and connecting the programmer to the connector JTAG1:
JTAG1 pin 2= TMS
JTAG1 pin 4= TCLK
JTAG1 pin 6= TDO
JTAG1 pin 8= TDI
Can This type of configuration be created/added to programmer selections ?
Will this work ?
Thank you.
Regards,
Rafal

 

[Admin]

Hello,
This is more of the question to programmer creators, I think.
Has anyone found solution how to read/write EC NPCX897KA0BX ?
I know method through keyboard connector is not working yet.
Has anyone tried to use JTAG programing like it is done for MEC Chips ?
To program this KBC chip under the MEC mode of programmer.
In motherboard NM-C262 soldering the resistor REC10 (1kΩ/5%, package 0402) to the board and connecting the programmer to the connector JTAG1:
JTAG1 pin 2= TMS
JTAG1 pin 4= TCLK
JTAG1 pin 6= TDO
JTAG1 pin 8= TDI
Can This type of configuration be created/added to programmer selections ?
Will this work ?
Thank you.
Regards,
Rafal

Check this Rafal